Welcome to
Sysmex Flow Cytometry Ireland!

For ordering please make sure you are in your local shop.
If you are from Ireland then please continue.
Otherwise please go to your country.

Go to my country Continue

Article successfully added.

CyFlow™ IgG2a Alexa Fluor™ 647

CyFlow™ IgG2a Alexa Fluor™ 647
Clonality: monoclonal
Regulatory Status: RUO
Source Species: Mouse
Laser: Red
Excitation Maximum: 650 nm
Isotype: IgG2a
Format/Fluorochrome: Alexa Fluor™ 647
Emission Maximum: 665 nm
Application: Flow cytometry (Isotype control)
Field of Interest: Isotype controls
Antigen: IgG2a Isotype Control
Clone: MOPC-173
Order number: AL914834
Concentration Unit mg/mL Concentration 0,1 Quantity 0.1 mg Volume 1.0 mL... more
Product information "CyFlow™ IgG2a Alexa Fluor™ 647"
Concentration Unitmg/mL
Concentration0,1
Quantity0.1 mg
Volume1.0 mL
ImmunogenThe transplantable plasmacytoma MOPC-173 was induced by intraperitoneal injection of mineral oils into BALB/c mice
Background InformationThe specificity of staining by monoclonal antibodies to target antigens should be verified by establishing the amount of non-specific antibody binding. Especially at higher concentration (more than 15 μ/ml) the antibody staining usually has consignable background. To this end a non-reactive immunoglobulin of the same isotype is included as a negative control for each specific monoclonal antibody used in a particular immunoassay. The monoclonal antibody MOPC-173, generated against an undefined antigen, does not react specifically with mouse, rat and human samples, and hence all the background that could be observed when working with this antibody would be a result of general nonspecific interactions between an mouse IgG2a molecule and the respective sample under the particular conditions. This shall help the customer to set up the experimental conditions so that the nonspecific binding of any antibody is abolished.
UsageThe reagent is designed as an isotype control for Flow Cytometry analysis. To establish the amount of non-specific antibody binding, match the concentration of the correct isotype to the recommended working concentration of the antigen-specific antibody. If the background signal of the isotype control is too high (usually when working antibody concentrations are above 10·µg/ml of incubation mixture), change the experimental conditions to reduce the background.
Storage BufferThe reagent is provided in stabilizing phosphate buffered saline (PBS) solution, pH ≈7.4, containing 0.09% (w/v) sodium azide.
StorageAvoid prolonged exposure to light. Store in the dark at 2-8°C. Do not freeze.
StabilityDo not use after expiration date stamped on vial label.
Similar products
Pacific Blue™
CyFlow™ IgG1 Pacific Blue™
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
Pacific Orange™
CyFlow™ IgG1 Pacific Orange™
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
FITC
CyFlow™ IgG1 FITC
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
Alexa Fluor™ 488
CyFlow™ IgG1 Alexa Fluor™ 488
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
PE
CyFlow™ IgG1 PE
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
PE-DyLight™ 594
CyFlow™ IgG1 PE-DyLight™ 594
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
PE-Cy5
CyFlow™ IgG1 PE-Cy5
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg
PerCP
CyFlow™ IgG1 PerCP
Antigen: IgG1 Isotype Control
Clone: MOPC-21
Application: Flow cytometry (Isotype control)
Regulatory Status: RUO
Quantity: 0.1 mg

* All prices are quoted net of the statutory value-added tax and shipping costs and possibly delivery charges, if not otherwise described

Need more information?
Need more information?
Service Hotline | Contact | Benefits
Service hotline
0333 320 3460 Mon-Fri, 9 am - 5 pm

Contact
Use our contact form